SMC Networks Barricade SMC7004VBR User Manual Download Page 64

Page: 64 / 122

DVANCED

ETUP

4-36

The following items are included on this screen:

Section

Description

INTERNET

Displays WAN connection type and status.

GATEWAY

Displays system IP settings, as well as DHCP and

Firewall status.

INFORMATION

Displays the number of attached clients, the

firmware versions, the physical MAC address for

each media interface, as well as the hardware

version and serial number.

Security Log

Displays illegal attempts to access your network.

Save

Click on this button to save a security log file.

Clear

Click on this button to delete the access log.

Refresh

Click on this button to refresh the screen.

DHCP Client Log

Displays information on all DHCP clients on your

network.

Release

Click on this button to confirm Dynamic settings.

Renew

Click on this button to refresh Dynamic settings.

Summary of Contents for Barricade SMC7004VBR



























































































































Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands

SMC Networks Barricade SMC7004VBR, User Manual

Search results

Summary of Contents for Barricade SMC7004VBR

Reviews:

Related manuals for Barricade SMC7004VBR

Brands by name

Popular brands