SMC Networks Barricade SMC7004VBR User Manual Download Page 7 | Manualshive

Page: 7 / 122

background image

vii

C

OMPLIANCES

FCC - Class B

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected

• Consult the dealer or an experienced radio/TV technician for help

EC Conformance Declaration - Class B

SMC contact for these products in Europe is:

SMC Networks Europe,
Edificio Conata II,
Calle Fructuós Gelabert 6-8, 2

o

, 4

a

,

08970 - Sant Joan Despí,
Barcelona, Spain.

This information technology equipment complies with the requirements of the Council
Directive 89/336/EEC on the Approximation of the laws of the Member States relating to
Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain
voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the
compliance with these Directives, the following standards were applied:

RFI

Emission:

* Limit class B according to EN 55022:1998
* Limit class A for harmonic current emission according to EN 61000-3-2/1995
* Limitation of voltage fluctuation and flicker in low-voltage supply system

according to EN 61000-3-3/1995

Immunity: * Product family standard according to EN 55024:1998

* Electrostatic Discharge according to EN 61000-4-2:1995 (Contact Discharge: ±4

kV, Air Discharge: ±8 kV)

* Radio-frequency electromagnetic field according to EN 61000-4-3: 1996 (80 -

1000MHz with 1kHz AM 80% Modulation: 3V/m)

«
...
5
6
7
8
9
...
»

Summary of Contents for Barricade SMC7004VBR



























































































































Reviews:

No comments

Related manuals for Barricade SMC7004VBR

Brand: ZyXEL Communications Pages: 2

Brand: Allied Telesis Pages: 22

PoleVault System A/V Source Inputs

Brand: Extron electronics Pages: 4

Brand: EMCIS Pages: 14

Brand: Paradyne Pages: 10

AT-8550/SP Series

Brand: Allied Telesis Pages: 114

Brand: Belkin Pages: 57

Brand: Z Microsystems Pages: 51

Brand: Paradyne Pages: 6

Brand: ADTRAN Pages: 9

Brand: Telestar Pages: 16

Brand: Matrix Switch Corporation Pages: 60

Brand: l-com Pages: 11

Brand: Gigabyte Pages: 10

Brand: Data-Tronix Pages: 15

Brand: Aegis Pages: 7

cnPilot Home R200 Series

Brand: Cambium Networks Pages: 136

Brand: Cambium Networks Pages: 208

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands