manualshive.com logo in svg

SMC Networks 6128L2, Management Manual

The SMC Networks 6128L2 is a high-performance network switch designed to deliver fast and reliable connectivity. For easy installation and setup, make sure to download the comprehensive user manual for free from our website - manualshive.com. Unlock the full potential of this product with our detailed installation manual.

Share
Download
background image

P

ORT

 C

ONFIGURATION

3-129

Setting Broadcast Storm Thresholds

Broadcast storms may occur when a device on your network is 
malfunctioning, or if application programs are not well designed or 
properly configured. If there is too much broadcast traffic on your 
network, performance can be severely degraded or everything can come to 
complete halt. 

You can protect your network from broadcast storms by setting a 
threshold for broadcast traffic for each port. Any broadcast packets 
exceeding the specified threshold will then be dropped.

Command Usage

•

Broadcast Storm Control is enabled by default.

•

Broadcast control does not effect IP multicast traffic.

•

The specified threshold applies to each individual port on the switch.

Command Attributes

•

Port 

– Port number.

•

Type 

– Indicates the port type. (100BASE-TX, 1000BASE-T, or SFP)

•

Protect Status

 – Shows whether or not broadcast storm control has 

been enabled. (Default: Enabled)

•

Threshold

 – Threshold as percentage of port bandwidth. (Options: 

64-1000000 packets per second; Default: 64 packets per second)

•

Trunk 

– Shows if a port is a trunk member. 

Summary of Contents for 6128L2































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6128L2

Eaton COOPER POWER SERIES Service Instructions Manual preview
COOPER POWER SERIES
Brand: Eaton Pages: 24
Eaton COOPER POWER SERIES Installation And Adjustment Instructions preview
COOPER POWER SERIES
Brand: Eaton Pages: 16
Eaton Crouse-hinds series Manual preview
Crouse-hinds series
Brand: Eaton Pages: 16
Eaton Cutler-Hammer AMPGARD Instructions preview
Cutler-Hammer AMPGARD
Brand: Eaton Pages: 4
Black Box SW730A Manual preview
SW730A
Brand: Black Box Pages: 26
ABB eOT Series Installation Instructions Manual preview
eOT Series
Brand: ABB Pages: 10
StarTech.com 8STSV211HDUA4K Quick Start Manual preview
8STSV211HDUA4K
Brand: StarTech.com Pages: 2
Gefen DVI-841 User Manual preview
DVI-841
Brand: Gefen Pages: 11
Ametek SIL IntelliPoint RF S*R*L Series Installation And Operating Instructions Manual preview
SIL IntelliPoint RF S*R*L Series
Brand: Ametek Pages: 93
Cabletron Systems 9F426-03 Appendix preview
9F426-03
Brand: Cabletron Systems Pages: 14
Hama 00176551 Operating Instructions Manual preview
00176551
Brand: Hama Pages: 56
Davey RainBank Installation Instructions preview
RainBank
Brand: Davey Pages: 2
BluStream SW41HDBT Quick Reference Manual preview
SW41HDBT
Brand: BluStream Pages: 4
Hama 39859 Operating Instructions Manual preview
39859
Brand: Hama Pages: 14
NA-DE 03009 Manual preview
03009
Brand: NA-DE Pages: 4
Vagner Pool PRO PIEZO 1 Instruction Manual preview
PRO PIEZO 1
Brand: Vagner Pool Pages: 5
Versitron SG70660M Installation Manual preview
SG70660M
Brand: Versitron Pages: 46
Lantech IPGS-5 Series User Manual preview
IPGS-5 Series
Brand: Lantech Pages: 29

Brands by name

Popular brands

Load more brands