manualshive.com logo in svg

SkyWave IDP 800 Series, Hardware Manual, Page: 69 / 102

Share
Download
SkyWave IDP 800 Series Hardware Manual Download Page 69

 

IDP 800 Terminal Series - Hardware Guide 

© SkyWave Proprietary                                                    57                                                   T209, Version 01 

4.8.1  Apply Dielectric Grease 

1.

 

Cut off one end of the tube of silicone lubricant. Adding the silicone lubricant 
(grease) protects the contacts. 

2.

 

Insert the tube into the male end of the mating connector (Figure 45).  

Figure 45  Apply Silicone Lubricant to Connector 

 

3.

 

Squeeze the lubricant into the mating connecter opening until it is full. Some 
lubricant may spill out.  

4.

 

Connect the cable connector to the terminal by aligning the corresponding connector 
key slot (Figure 33) and gently push together. 

5.

 

Tighten the cable connector with hand pressure by rotating the locking collar on the 
cable connector clockwise. Do not use a wrench. A tactile click is felt when the 
collar is properly engaged. 

Figure 46  Cable Connector and Locking Collar 

 

6.

 

Wipe off any extra lubricant around the connector.  

Fill this 

cavity 

Summary of Contents for IDP 800 Series







































































































Reviews:

No comments