SkyWave IDP 800 Series Hardware Manual Download Page 66 | Manualshive

Page: 66 / 102

SkyWave IDP 800 Series Hardware Manual Download Page 66

IDP 800 Terminal Series - Hardware Guide

T209, Version 01 54 © SkyWave Proprietary

Figure 41 Apply Silicone to Hole in Asset

6.

Lower the remote antenna onto the mounting surface.

The straight SMA cable connector can be lowered straight down onto the
mounting surface.

The right angle SMA cable connector, not shown, must be pivoted down onto the
mounting surface to fit the right angle cable and connector through a larger
clearance hole. Additional care is required with this installation to ensure the
right angle cable and connector does not smear the silicone around the clearance
hole when attempting to pivot the antenna into position.

7.

Apply a generous bead of silicone around the entire perimeter of the remote
antenna enclosure. The two vertical slots shown in Figure 42 are vent features
and must not be filled with silicone.

Note:

If the large clearance hole required for the right angle SMA cable
connector is considered too large, there is the option to use a smaller
clearance hole in the mounting surface and install the cable from
inside the asset after the antenna has been adhered with silicone.

In this case, first confirm there is enough room from inside the asset to
thread the SMA cable connector by hand and clearance for the wrench
to apply the final torque.

Also note that the silicone used to mount the antenna must be fully
cured before the cable can be installed from the inside otherwise the
seal and mounting are compromised.

«
...
64
65
66
67
68
...
»

Summary of Contents for IDP 800 Series







































































































Reviews:

No comments