manualshive.com logo in svg

SkyWave IDP 800 Series, Hardware Manual, Page: 21 / 102

Share
Download
SkyWave IDP 800 Series Hardware Manual Download Page 21

 

IDP 800 Terminal Series - Hardware Guide 

© SkyWave Proprietary                                                    9                                                   T209, Version 01 

2 

Compliance  

The IDP-800 terminal has obtained the following certifications:  

Inmarsat Type Approval  

 

pending 

Industry Canada 

 

ICES-003 

 

RSS-170, Issue 2, Spectrum Management and Telecommunications Policy, 
Radio Standard 

 

RSS-102 (radiation safety per Safety Code 6) 

FCC Part 15 and Part 25 

 

CFR Title 47: Telecommunication, Part 15  

 

CFR Title 47: Telecommunication, Part 25 - Satellite Communications 

 

OET 65 - Radiation Safety 

R&TTE Directive 1999/5/EC (CE Mark) 

 

EN 301 426 V1.2.1 (2001-10), Satellite Earth stations and Systems (SES); 
Harmonized EN for Low data rate Land Mobile satellite Earth Stations (LMES) 
and Maritime Mobile satellite Earth Stations (MMES) not intended for distress 
and safety communications operating in the 1,5/1,6 GHz frequency bands 
covering essential requirements under article 3.2 of the R&TTE Directive 

 

EN 301 489-20 V1.2.1 (2002-11), Electromagnetic compatibility and Radio 
spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for 
radio equipment and services; Part 20: Specific conditions for Mobile Earth 
Stations (MES) used in the Mobile Satellite Services (MSS)  

 

EN 301 489-1 V1.9.2 (2011-09) - Electromagnetic compatibility (EMC) 

 

IEC 60950-22:2005 (1st Edition) - Safety 

 

IEC 60950-1:2005 (2nd Edition); Am 1:2009  

CAUTION

 

This certification is void if  
batteries other than those specified  
in Section 3.8.1 are used. 

 

IEC 62311 - Radiation safety 

 

 

Summary of Contents for IDP 800 Series







































































































Reviews:

No comments