manualshive.com logo in svg

SkyWave IDP 800 Series, Hardware Manual, Page: 31 / 102

Share
Download
SkyWave IDP 800 Series Hardware Manual Download Page 31

 

IDP 800 Terminal Series - Hardware Guide 

© SkyWave Proprietary                                                    19                                                   T209, Version 01 

3.3  RF Connector 

The IDP-800 is optionally available to support a remote antenna. The remote antenna 
terminal variant uses an SMA panel connector.  

The terminal must only be used with an active SkyWave antenna. Refer to APPENDIX A 
for antenna order part numbers. 

Table 13 

RF Connector 

Parameter 

Value 

Antenna Connector 

SMA female, normal polarity 

Maximum Cable Length 

8 m 

3.3.1  Antenna Cut Detection 

For remote antenna versions, the terminal can detect when the antenna is disconnected. It 
detects the antenna disconnect by monitoring the DC current to the antenna when it is 
receiving either a GPS or IsatData Pro signal.  

3.4  Pass-Through Mode 

The terminal operates in pass-through mode when there is no application firmware 
present. A block diagram of pass-through mode is shown in Figure 9. In pass-through 
mode, the terminal connects the modem's serial interface to the terminal's  
RS-232 port.  

Figure 9 

Pass-Through Mode Signals 

 

The terminal's I/O lines are configured as per Table 14 when in pass-through mode. The 
modem's serial data and the EVENT_NOTIFICATION pins are connected to the 
terminal's external connector.  

Table 14 

Pass-Through Mode Power 

I/O Pin 

State 

Specification 

I/O 02 

Output 

Connected to EVENT_NOTIFICATION 

I/O 01 and I/O 03 

Analog Input 

Do not use 

RS-232 

RS-232 

Disabled if no valid RS-232 level on receiver 

When in pass-through mode, there are no inputs for the application controller to sample. 
Pass-through mode time specifications are given in Table 15. 

Terminal 

Modem 

RS-232 

EVENT NOTIFICATION 

I/O 02 

RS-232 

Summary of Contents for IDP 800 Series







































































































Reviews:

No comments