SkyAzúl Greer MG514 Installation, Calibration, And Service Manual Download Page 34

Page: 34 / 90

2.6.8

Menu 07 - Radius/Moment

This menu is used to calibrate the radius and moment of the boom.

1. Press the

Next

Prev

butto

ns until “07 Radius/Moment” appears in the information window at

the right.

ENSURE THE CRANE IS SET UP IN ACCORDANCE WITH THE MANUFACTURER’S

OPERATION MANUAL FOR MAXIMUM STABILITY. ENSURE THAT ALL BOOM

EXTENSIONS AND LOADS LIFTED ARE WITHIN THE APPROPRIATE LOAD CHARTS

AND LIMITS. FAILURE TO COMPLY WITH MANUFACTURER’S LIMITS MAY RESULT IN

SERIOUS INJURY OR DEATH.

IMPORTANT!

ANY ATTACHMENTS ON THE SIDE OR TIP OF THE BOOM DURING THESE TESTS CAN

CAUSE INACCURACY IN THE MAIN BOOM MOMENT IF THE SETUP OR STORED

INFORMATION IS INCORRECT.

RCI514 Radius Moment Calibration

BOOM MODE A: Perform two Radius Moments, fully retracted and fully extended.

BOOM MODE B: Perform four Radius Moments at fully retracted, ½ Boom Length, ¾ Boom Length and
fully extended.

Enter Calibration Mode and press Next button to menu to 07 Radius / Moment

SkyAzúl, Equipment Solutions

www.skyazul.com

301-371-6126

Summary of Contents for Greer MG514



























































































Search results

Summary of Contents for Greer MG514

Reviews:

Related manuals for Greer MG514

Brands by name

Popular brands

SkyAzúl Greer MG514, Installation, Calibration, And Service Manual

Search results

Summary of Contents for Greer MG514

Reviews:

Related manuals for Greer MG514

Brands by name

Popular brands