Skov DOL 535 Technical Manual Download Page 57

Page: 57 / 68

DOL 535 • DOL 539

Technical Manual

Non-controlling production controller

Terminal

Signal level

> 9 V = The distribution shutter leads the feed to this house.

8.2.2.1 Feed weigher sharing signals

Check that the shared signals are connected correctly.

In the menu

Technical | Service | Manual/auto

both the controlling and the non-controlling controller are set to

manual =

In the menu

Technical | Service | Manual/auto| Production | Feed weigher

the signals are controlled and ver-

ified.

Signal control

1. Set

Weigher request relay

on one of the controllers.

2. Check that

the shared signal

= approx 10 V on the other controller.

3. Set

Weigher request relay

OFF

on one of the controllers.

4. Check that

the shared signal

= approx 0 V on the other controller.

Repeat the procedure based on the other controller.

Checking shutter signals

1. Set

Shutter relay

on the controlling climate and production controller.

2. Check that the distribution shutter conveys the feed to the controlling livestock house.

3. Check that

Shutter position

= approx 0 V on both controllers.

4. Set

Shutter relay

OFF

on the controlling climate and production controller.

5. Check that the shutter conveys the feed to the non-controlling livestock house.

6. Check that

Shutter position

= approx 10 V on both controllers.

Remember to set

Manual/auto

OFF

in the menu

Technical | Service | Manual/auto

Summary of Contents for DOL 535





































































Search results

Summary of Contents for DOL 535

Reviews:

Related manuals for DOL 535

Brands by name

Popular brands

Skov DOL 535, Technical Manual

Search results

Summary of Contents for DOL 535

Reviews:

Related manuals for DOL 535

Brands by name

Popular brands