manualshive.com logo in svg

Skov DOL 535, Technical Manual

Share
Download
Skov DOL 535 Technical Manual Download Page 42

DOL 535 • DOL 539

42

Technical Manual

If the weigher is not empty but it contains less than 10 kg, the
weigher cannot empty its contents. The house controller acti-
vates the solenoid coil at regular intervals (3-4 seconds).

When the quantity of feed in the weigher is insufficient, the
weigher must either be emptied manually by activating its emp-
tying mechanism or by adding more feed to the weighing con-
tainer through feed requirements.

See also the testing section in the DOL 9940 Technical user
guide.

5.2.1.5 Testing shared feed weigher (shared with shutter) - drum weigher and
DOL 9940

Select the menu 

 

 

Technical | Manual/auto.

Then select 

Production | Feed weigher

.

Activate 

Feed weigher request relay

 to retrieve a signal from

the weigher.

Test the shutter relay from the controlling production controller
by selecting 

Shutter relay

 to make the shutter change position.

5.2.1.6 Testing shared feed weigher (via controllers in network)

Sharing is tested by carrying out one feeding on all controllers using the same feed weigher. Carry out the feed-
ing on one production controller at the time.

5.2.1.7 Testing feed separation shutter (separate destination feeding for males
and females)

Select the menu 

 

 

Technical | Manual/auto.

Then select 

Production | Feed separation shutter

 and activate 

Manual mode

.

Activate 

Shutter relay

 and check that the shutter has changed

position.

Deactivate 

Shutter relay

 and check that the shutter has

changed position to the other cross auger.

5.2.1.8 Testing the electronic silo weigher

Select the menu 

 

 

Technical | Manual/auto |

 

Production

 

|

 

Electronic silo weigher | 

select the silo

Summary of Contents for DOL 535





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands