Skov DOL 535 Technical Manual Download Page 11

Page: 11 / 68

DOL 535 • DOL 539

Technical Manual

Select the menu

Techical | Installation | Manual in-

stallation | Climate | Sensors | Temperature sensor

Activate

Use shared outside temperature sensor

Select the controller where the outside temperature sensor is
connected.

The name of the controller providing the outside temperature is
shown in the display.

3.5 The menu Installation

3.5.1 Layer house

House type

Selecting the house type

House settings

Setting the number of rows and number of tiers per row (layers in cages).

Setting the number of compartments (aviary).

3.5.2 Animals

Animals

Setting up how the animal groups are composed.

Broiler:

Sexed animals / Females and males / Only females / Only males

Breeder:

Females and males / Only females / Only males

Layer:

Females

3.5.2.1 Animal groups

Dividing the animals into groups can give a more precise registration of stocked, dead and livability for the differ-
ent sections in the livestock house.

It is possible to divide the animals into groups for layers in cages and aviary.

If only one group is created, it applies to the entire house.

Summary of Contents for DOL 535





































































Search results

Summary of Contents for DOL 535

Reviews:

Related manuals for DOL 535

Brands by name

Popular brands

Skov DOL 535, Technical Manual

Search results

Summary of Contents for DOL 535

Reviews:

Related manuals for DOL 535

Brands by name

Popular brands