manualshive.com logo in svg

Skov DOL 535, Technical Manual

Share
Download
Skov DOL 535 Technical Manual Download Page 44

DOL 535 • DOL 539

44

Technical Manual

Activate and deactivate the water meter relay.

Check that the solenoid valve changes.

Read whether the values change to check for connection to the
water meters.

Water level

Read whether the values are correct in relation to the current
water level.

5.2.1.12 Testing door opening

Testing the door opening can be used for pop-holes, winter garden, nests and scratching area.

The test is to show if the door can open, close and stop.

Select the menu 

 

 

Technical | Manual/auto.

Then select 

Climate | FreeRange | Pop holes

 or 

Winter garden | Pop holes control

 or 

Winter garden control

or 

Production | Nest

 or 

Scratching area

 and activate 

Manual mode

.

Then select in turn 

Open

, 

Close

 and 

Stop

.

Check that the door changes position as expected.

5.2.1.13 Testing egg counter

Select the menu 

 

 

Technical | Manual/auto.

Then select 

Production | Egg counters

Check that the egg counter is closed correctly in relation to the
intended location.

Look in the menu 

 

 

Technical | Installation | Manual in-

stallation | Production | Eggs | Configure eggs per pulse

 how

many eggs are required to trigger a pulse and run this number
of eggs through so that the result changes.

Egg counter inputs

Check that the input is connected correctly in relation to the in-
tended position(s).

5.2.1.14 Testing the poultry scale

Select the menu 

 

 

Technical | Manual/auto.

Then select 

Production | Bird scale

Summary of Contents for DOL 535





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands