Skov DOL 535 Technical Manual Download Page 8

Page: 8 / 68

DOL 535 • DOL 539

Technical Manual

3 Installation guide

3.1 Selecting components

There are two ways to carry out installation of the controller.

At the initial installation:

Use Installation wizard which will guide you through all the options of the functions.

At adaptation of the existing installation:

Use the menu

Technical | Manual installation

which enables you

to go directly to the relevant function.

Select components in the installation menu of the controller.

(

Technical | Installation | Start installation

Manual

installation

It is not possible to select more components than there is avail-
able I/O for.

You must therefore be aware of whether the controller accepts
your wish to connect a component

If missing I/O, you can:

• install extra I/O modules (if these are available).

• uninstall components.

While functions are selected in the

Installation

and

Show con-

nections

setup menus, all alarms will be delayed. Thus, no

alarms will be generated until 2 minutes after the last change in
the installation menu.

This is indicated as info in the alarm menu for as long as the
delay is active.

This does not apply to alarms from CAN bus communication (I/
O modules).

3.2 Select type of unit of measurements

Unit of measurements

The controller and display units as either metric or US units.

3.3 View week number

Show week number

View of week number at the top of all pages.

3.4 Connecting Components

The main part of the connection terminals is universal. Different components can therefore be installed using the
individual terminals.

Summary of Contents for DOL 535





































































Search results

Summary of Contents for DOL 535

Reviews:

Related manuals for DOL 535

Brands by name

Popular brands

Skov DOL 535, Technical Manual

Search results

Summary of Contents for DOL 535

Reviews:

Related manuals for DOL 535

Brands by name

Popular brands