ES
28
Solución de problemas
Problema
Causa
Solución
La corona perforadora se ha atascado en el material.
Presión excesiva sobre el material.
Reduzca la presión en la herramienta.
Modo percutor activado.
Asegúrese de que el modo percutor esté desactivado para este
tipo de aplicación.
Corona perforadora incompatible.
Asegúrese de que el diámetro y la velocidad máxima de la
corona sean adecuadas para este taladro.
Restos de suciedad acumulados dentro de la
corona perforadora.
Limpie regularmente los restos de suciedad acumulados en la
corona perforadora.
El taladro es incómodo de manejar debido a la
vibración.
Ha utilizado la herramienta durante demasiado
tiempo.
Realice pausas regularmente y lea toda la información relativa
a la vibración.
La herramienta no se enciende.
No hay alimentación eléctrica, fusible fundido o el
interruptor diferencial ha saltado.
Sustituya el fusible o reinicie el interruptor diferencial. Si
vuelve a fundirse el fusible, contacte inmediatamente con un
servicio técnico Silverline.
Cable de alimentación dañado.
Contacte con un servicio técnico autorizado Silverline.
Interruptor de encendido/apagado averiado.
Contacte con un servicio técnico autorizado Silverline.
Motor averiado.
Contacte con un servicio técnico autorizado Silverline.
Velocidad de rotación lenta.
Sobrecalentamiento del motor.
Apague la herramienta y deje que se enfríe. Compruebe que
los orificios de ventilación no estén obstruidos.
Velocidad de rotación lenta, no rotación o chispas en
los orificios del motor.
Escobillas de carbon desgastadas.
Contacte con un servicio técnico autorizado Silverline.
Vibración o ruido anormal.
Falta de grasa en la caja de engranajes.
Añada o sustituya la grasa.
Partes internas excesivamente desgastadas.
Contacte con un servicio técnico autorizado Silverline.
El taladro no rompe el material en modo cincel.
Material demasiado denso.
Herramienta no apta para romper este material.
Punta del cincel desgastada.
Sustituya el cincel.
El cincel está rotando.
Ajuste la herramienta correctamente.
Seleccione el modo de parada de seguridad.
Perforación poco eficiente en mampostería.
Modo percutor desactivado.
Seleccione el modo percutor.
Punta de la broca desgastada o dañada.
Sustituya la broca SDS Plus.
Material demasiado denso.
La velocidad de perforación en mampostería es más lenta.
Utilice antes una broca piloto para perforar más fácilmente.
Las brocas SDS Plus no encajan correctamente en el
portabrocas.
Suciedad acumulada en el portabrocas.
Limpie los restos de suciedad acumulado con una aspiradora.
Utilice siempre un protector para polvo para evitar que la
suciedad se pueda acumular dentro del portabrocas.
633821/952118_Manual.indd 28
03/07/2019 08:53
Summary of Contents for 633821
Page 3: ...silverlinetools com 3 Fig I Fig II 633821 952118_Manual indd 3 03 07 2019 08 53...
Page 4: ...4 633821 952118_Manual indd 4 03 07 2019 08 53...
Page 48: ...48 Notes 633821 952118_Manual indd 48 03 07 2019 08 53...
Page 49: ...silverlinetools com 49 Notes 633821 952118_Manual indd 49 03 07 2019 08 53...