MIG/MAG Combination Gas/No Gas Welder
30-135A
7
silverlinetools.com
General Safety
WARNING: Read this manual before operating, adjusting and servicing this welder.
WARNING SIGHT RISK: Arc glare can permanently damage your eyesight.
Always use a suitable
welding mask, face shield or helmet. Always check condition of eye protection before use.
WARNING FIRE RISK: All flammable materials must be removed from the welding area.
WARNING WELDING FUMES: Toxic gases are given off during welding.
Always use in a
well-ventilated area.
WARNING BURN RISK: Wear welding gloves at all times when welding.
They will reduce the
risk of burn injuries and ultra-violet radiation. In addition, wear a leather apron to protect from spatter
and a cap when welding overhead.
WARNING: This appliance is not intended for use by persons (including children) with
reduced, physical or mental capabilities or lack of experience or knowledge unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children must be supervised to ensure that they do not play
with the appliance.
Keep work area clear - Cluttered areas and benches invite injuries
• Consider work area environment
- Do not expose welder to rain
- Do not use welder in damp or wet locations
- Keep work area well lit
• Keep other persons away.
Do not let persons, especially children, not involved in the work touch
the tool or the extension cord and keep them away from the work area
WARNING: Not using protective equipment or appropriate clothing can cause personal injury
or increase the severity of an injury.
• Do not abuse the power cable.
Never pull the power cable to disconnect it from the socket.
Keep the power cable away from heat, oil and sharp edges. Damaged or entangled power cables
increase the risk of electric shock
• Do not overreach.
Keep proper footing and balance at all times
• Maintain tools with care
- Inspect tool power cables periodically and have them repaired by an authorised service facility
if damaged
- Inspect extension cables periodically and replace if damaged
• Disconnect -
Disconnect welders from the power supply when not in use, before servicing and
when changing accessories
WARNING: The use of accessories or attachments not recommended by the manufacturer
may result in a risk of injury to persons.
• Stay alert
- Watch what you are doing, use common sense and do not operate the tool when you are tired
- Do not use a welder while you are under the influence of drugs, alcohol or medication
WARNING: A moment of inattention while operating power tools may result in serious
personal injury.
• Check damaged parts
WARNING: Do not use the welder if the on/off switch does not switch the tool on and off.
The switch must be repaired before the welder is used.
• Have your tool repaired by a qualified person.
This welder complies with the relevant safety
rules. Repairs should only be carried out by qualified persons, otherwise this may result in
considerable danger to the user
WARNING: When servicing use only identical replacement parts.
WARNING: If the power cable is damaged it must be replaced by the manufacturer or an
authorised service centre.
WARNING: Power tool mains plugs must match the mains socket.
Never modify the plug in
any way. Do not use any adaptor plugs with earthed (grounded) power tools. Unmodified plugs and
matching sockets will reduce risk of electric shock.
Welding Safety
WARNING: DO NOT strike an arc close to the gas bottle.
WARNING: DO NOT lift the welder with a gas bottle attached.
WARNING: DO NOT use a welder for pipe thawing.
WARNING: AVOID unintentional arcing of the welder.
Switch off the welder when not in use.
IMPORTANT: Use of welding machines creates powerful magnetic fields.
This may disturb the
operation of sensitive electronic equipment. Pacemaker wearers should consult a doctor before using
a welding machine.
IMPORTANT: Do not overload a mains circuit.
Check that your mains wiring is capable of
delivering the required current safely. If unsure consult a professional electrician before use.
• Welding produces toxic fumes and can reduce oxygen levels in the work area. Always
work in a well-ventilated area.
Avoid inhaling welding fumes, use a suitable respirator where
appropriate
• Some metal parts may have zinc, lead, cadmium or other coatings. Attempting to weld
through these coatings can produce highly toxic fumes.
Always remove all coatings before
welding
• If you experience irritation to the lungs, throat or eyes whilst welding,
STOP IMMEDIATELY
and seek fresh air
• Welding produces extremely high levels of UV light. To prevent eye damage, ALWAYS use
an approved welding face mask.
Under no circumstances look directly at the arc
• The light produced when arc welding can be attractive to look at, especially to children.
Always prevent other people from viewing the arc welding light with unprotected eyes
• If there is a possibility of other people approaching the work area, erect suitable
screening to protect them from the light / glare
• Always replace the welder face mask glass as soon as it shows any signs of wear or
damage
• To prevent skin damage, ALWAYS wear a suitable fire-proof long sleeved jacket, heat proof
gloves, and cap. Keep covered up
• Always remove any flammable materials (e.g. cigarette lighter, matches) from your
clothing before welding
• Always keep a fire extinguisher nearby when welding
• Sparks generated while welding can ignite flammable materials easily in the welding
area.
So it is important to remove flammable materials before commencing welding
• Only weld when the work area and all workpieces are dry
• Do not weld sealed containers (e.g. fuel tanks, air tanks, oil drums).
The heat generated
from welding can cause sealed containers to burst without warning
• Be aware of transferred heat. Metal parts can conduct heat away from the work area and
cause ignition of flammable materials
• Be aware that welded parts will remain hot for some time after joining.
Allow to cool
completely before handling, or leaving unattended
• Never weld where flammable gases, liquids or dust are present
• Ensure that there is always a responsible person nearby to alert you to any fire, or to call
help in an emergency
• Workpieces with burred edges can damage the torch cable.
Always ensure the torch cable
will not be damaged as it moves over a surface
Wire feed
• Caution: The tip of welding wire can be very sharp, and is fed with adequate force to
puncture skin
• Keep the welding machine switched off until you are ready to begin welding.
Never point
the torch towards people or animals
380736_Manual.indd 7
13/10/2017 17:15
Summary of Contents for 30-135A
