Silverline 2300W Generator 2.2kV Manual Download Page 10

Page: 10 / 42

Earthing the Generator

• It is strongly recommended that this generator is earthed. The generator

MUST be earthed when using devices that require an earth connection
in their plug

• To earth the generator, connect a 10 mm

insulated copper wire to the

generator's Earth Point (9) and to an earthing rod of galvanised steel, set
in the ground to a depth of 1 metre

Operating the Generator

1. Always start and allow the generator to warm up for a minimum

of 5 minutes before using the AC outputs. This will improve fuel
efficiency and reduce wear, increasing the service life of your
product

2. Ensure the AC Switch (5) is set to OFF
3. Plug your powered device into the correct Socket (6 or 8)
4. Move the Output Switch (7) towards the chosen Socket
5. Move the AC Switch (5) to ON
6. Observe the Voltmeter (4) to check the output voltage is correct for

the device attached

7. When the connected device is switched on, it is normal for the

generator engine to change speed

Cleaning and Maintenance

•   Only clean when Generator has fully cooled down
•   Use a mild soapy solution and a stiff brush
•   Rinse with clean water
•    Dry as thoroughly as possible – parts of this product will corrode if

left wet

• Only carry out maintenance when the Generator has fully cooled down
• Maintenance should be adjusted according to use and environment.

Generally, the more use and/or the harsher the environment, the more
frequent the maintenance

Cleaning the air filter element

1. Remove the two screws at the top and bottom of the Air Filter Cover

(10) and gently pull the cover off

2. Remove Air Filter (11), noting which way around it faces
3. Wash the air filter in a suitable fluid (available from most garden

machinery retailers)

4. Replace the air filter by reversing this procedure

Replacing and adjusting the spark plug

1. Pull the ignition lead off the Spark Plug (16) Fig. C
2. Unscrew the Spark Plug (16) using the socket supplied
3. Adjust the gap (see specification) using a feeler gauge. Clean using

a wire brush OR replace using a recommended spark plug (see
specification)

4. Replace spark plug and tighten firmly with the socket and bar NOTE:

be careful not to cross or overtighten the threads

5. Refit ignition lead

Changing the engine oil

1. Start and run the engine for around 2 minutes to warm the oil, then

switch off

2. Place the generator above a large oil draining bowl (Silverline tools

recommend product 675089) Make sure the Drain Plug (26) is above
the centre of the bowl

3. Using a 10mm socket and long extension, undo (anticlockwise) the

Drain Plug (26)

4. Allow the oil to drain fully for a minimum of 10 minutes
5. Tip the generator a little to get all of the waste oil out
6. Replace the Drain Plug (26) and tighten firmly with a ratchet
7. To replace the oil, see Preparing the Generator
8. Contact your local waste facility for advice about disposal of waste

engine oil

Storage

• Be careful not to hit or cut the fuel tank, or fuel lines, when the unit is

placed on the ground

• Do not let the tool fall, or it may be damaged and become unsafe
• When you finish working, clean the unit thoroughly
• Inspect the entire unit and tubes for damage, including loose or missing

components

• Store the unit away from direct sunlight
• Do not store in a nylon bag as this can encourage the formation of

mould

• Use a small brush to clean off the outside of the unit and keep the air

vents free from obstructions. Do not use water or a hose to clean the
unit

• Ensure that fuel and oil is stored in a safe place, away from heat, direct

sunlight, any source of ignition, and out of reach of children

Storage for an extended period:

Whenever the machine is out of use for an extended period of time,
proceed as follows:
• Give the unit an overall cleaning and a thorough check
• Empty the fuel tank completely, then clean the carburettor and lines by

running the tool until it stops from lack of fuel

• Protect all metal engine parts from corrosion by coating them with oil
• Remove the spark plug, put several drops of oil into the cylinder through

the spark plug hole and then pull the recoil starter 2 to 3 times in order
to distribute the oil evenly. Replace the spark plug and spark plug lead

• Clean the air filter as described in the air filter section

Troubleshooting

Power loss or sudden engine cut-out

• Check whether the fuel tank is empty
• Check if there is water in the mixture. Drain and rinse the fuel system

with petrol

• Check if the air filter is dirty. Clean the air filter

Starting a flooded engine

1. Disconnect the spark plug lead and use a spark plug wrench to

remove the spark plug by turning it anticlockwise