Silex technology BR-310AC User Manual Download Page 102

Page: 102 / 108

BR-310AC User's Guide

TCP/IP Configuration
DHCP

Details

Enable/Disable the DHCP protocol.
To assign an IP address using DHCP, the DHCP server must be running in your
subnetwork.

Range

ENABLE/DISABLE

Default Value

DISABLE

IP Address

Details

Set the IP address.
If the DHCP is enabled on your network, the IP Address obtained from it will be
applied.

Range

0.0.0.0 - 255.255.255.255

Default Value

0.0.0.0

Subnet Mask

Details

Set the subnet mask.
If the DHCP is enabled on your network, the Subnet Mask obtained from it will
be applied.

Range

0.0.0.0 - 255.255.255.255

Default Value

0.0.0.0

Note

When set to "0.0.0.0", a subnet mask appropriate for the IP address is
automatically assigned.

Default Gateway

Details

Set the gateway address.
If "0.0.0.0" is set, this setting is disabled. When the DHCP is enabled on your
network, the Default Gateway obtained from it will be applied.

Range

0.0.0.0 - 255.255.255.255

Default Value

0.0.0.0

Summary of Contents for BR-310AC












































































































Search results

Summary of Contents for BR-310AC

Reviews:

Related manuals for BR-310AC

Brands by name

Popular brands

Silex technology BR-310AC, User Manual

Search results

Summary of Contents for BR-310AC

Reviews:

Related manuals for BR-310AC

Brands by name

Popular brands