Silex technology BR-310AC User Manual Download Page 56

Page: 56 / 108

BR-310AC User's Guide

Configuration

Access the Web configuration interface of the Access Point using a Web browser (Internet
Explorer, Safari, etc) on your PC. Enter the PIN code and start the WPS connection from
the Access Point.

Enter the PIN code to start

the WPS connection

Access Point

Go back to the

Smart Wireless Setup

page of the BR-310AC and click the

Smart

Wireless Setup Execution

button.

- The method to enter the PIN code on Access Point will differ depending on each Access Point. For details,

refer to the operating manual that came with your Access Point.

Note

- If Smart Wireless Setup is started on the BR-310AC earlier than the Access Point, the configuration may fail.

TIP

Summary of Contents for BR-310AC












































































































Search results

Summary of Contents for BR-310AC

Reviews:

Related manuals for BR-310AC

Brands by name

Popular brands

Silex technology BR-310AC, User Manual

Search results

Summary of Contents for BR-310AC

Reviews:

Related manuals for BR-310AC

Brands by name

Popular brands