Silex technology BR-310AC User Manual Download Page 46

Page: 46 / 108

BR-310AC User's Guide

Connect the AC adaptor to the BR-310AC and the AC plug to the outlet.

BR-300AN

Outlet

AC adaptor

Turn on the non-wireless device connected to the BR-310AC.

During the MAC address resolution, the WLAN LED and STATUS LED will flash Green
alternately. When the LED status has changed from it, the BR-310AC will be ready to
configure using Smart Wireless Setup.

WLAN

STATUS

The LEDs flash Green alternately

during the MAC address resolution

BR-300AN

- Depending on the non-wireless device you have connected, further network settings may need to be

configured to that device. In such a case, please configure it according to the operating manual that came
with your device.

- When you turn on the BR-310AC and your non-wireless device, be sure to turn on the BR-310AC first. Do

not press the push switch then.

Note

Summary of Contents for BR-310AC












































































































Search results

Summary of Contents for BR-310AC

Reviews:

Related manuals for BR-310AC

Brands by name

Popular brands

Silex technology BR-310AC, User Manual

Search results

Summary of Contents for BR-310AC

Reviews:

Related manuals for BR-310AC

Brands by name

Popular brands