Silex technology BR-310AC User Manual Download Page 20

Page: 20 / 108

BR-310AC User's Guide

Configuration Mode

Normal Mode (Single Client Mode)

- This bridges other protocols.

Normal Mode (Multi-Client Mode)

- This bridges TCP/IP (IPv4, IPv6) only.

TCP/IP

Network layer

ARP, IP

Transport layer

TCP, UDP

Application layer

HTTP, DNS(simple reply function only), DHCP (simple server function only),
NetBIOS over TCP/IP (Name Service only), JCP, FLDP, FLDP/BR
* JCP, FLDP, FLDP/BR are the silex proprietary protocols.

TCP/IP

Application layer

FLDP, FLDP/BR (only on a LAN port), SX_SMP
* FLDP, FLDP/BR, SX_SMP are the silex proprietary protocols.

TCP/IP

Application layer

FLDP, FLDP/BR (only on a LAN port), SX_SMP
* FLDP, FLDP/BR, SX_SMP are the silex proprietary protocols.

2-4. Software Specification

Summary of Contents for BR-310AC












































































































Search results

Summary of Contents for BR-310AC

Reviews:

Related manuals for BR-310AC

Brands by name

Popular brands

Silex technology BR-310AC, User Manual

Search results

Summary of Contents for BR-310AC

Reviews:

Related manuals for BR-310AC

Brands by name

Popular brands