SignaMax 065-7700 User Manual Download Page 164

Page: 164 / 199

Hardened Managed PoE Ethernet Switch

User’s Manual 163

Location:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server location

command to specify and

no snmp-server

location

command to remove location for SNMP.

Command Syntax:

snmp-server location LOCATION
no snmp-server location

LOCATION The location for SNMP.

Example:

The following example specifies location (

location

) for SNMP:

switch_a(config)#snmp-server location location
switch_a(config)#

Contact:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

snmp-server contact

command to specify and

no snmp-server

contact

command to remove contact for SNMP.

Command Syntax:

snmp-server contact CONTACT
no snmp-server contact

CONTACT The contact for SNMP.

Example:

The following example specifies contact (

contact

) for SNMP:

switch_a(config)#snmp-server contact contact
switch_a(config)#

Trap Community Name:

Summary of Contents for 065-7700








































































































































































































Search results

Summary of Contents for 065-7700

Reviews:

Related manuals for 065-7700

Brands by name

Popular brands

SignaMax 065-7700, User Manual

Search results

Summary of Contents for 065-7700

Reviews:

Related manuals for 065-7700

Brands by name

Popular brands