manualshive.com logo in svg

SIG DORN IER Do 217, Assembly Manual, Page: 8 / 28

Share
Download
SIG DORN IER Do 217 Assembly Manual Download Page 8

. 

 
16.

 
Plank the upper center section of the wings. Prepare the center section sheeting as shown in drawings. Fit the front piece 
first then cut the rear to fit in the remaining space. A neat trick to get the radius in the corner of the sheets is to trace around 
a quarter.
 

 
17.

 
Add the 1/16"x3/16" (1.5x4.8mm) cap strips on the top of the remaining ribs.

 

 
18.

 
You can now remove this wing panel from the building board, cut away the 
sheeting from the aileron area, rough shape the leading edge, trim the excess 
sheeting from the tip and true up the sheeting at the root rib.

 
19.

 
Set this panel aside and build the other panel using steps #1 through #18.

 
20

 
Make the servo wire guide tubes by 
rolling a 2"x11" (50.8x279.4mm) piece 
of typing paper tightly around a section 
of 3/8" (9.5 mm) dowel then insert this 
dowel and paper into the holes.

 

 

 
21.

 
When the tube is in position, withdraw 
the dowel and let the paper unwind in 
the holes. Tack-glue the tubes in the 
ribs to keep them from shifting.

 
Trim the inside end of the tube at an angle to ease the insertion of the servo wires.

Summary of Contents for DORN IER Do 217





























Reviews:

No comments