SIG DORN IER Do 217 Assembly Manual Download Page 15 | Manualshive

Page: 15 / 28

SIG DORN IER Do 217 Assembly Manual Download Page 15

.

69.

Glue on F-11, F-12, and the 1/4" (6.4
mm) square parts at the nose.

70.

Glue in the 1/8"x1/4 " (3.2x6.4mm)
stabilizer supports.

71.

Glue in the 1/4" (6.4mm) square balsa
wing hold down plate supports ahead of
F-6 and below F-12.

72.

Locate bulkheads F-4, F-5, and F-6 and glue onto one fuselage side, making sure they are perpendicular to the side.

73.

Glue the other side to these bulkheads.

74.

Glue the 3 F-20s together then glue
them onto the 1/4" (6.4mm) square
wing hold down supports and F-6. This
will help hold the fuselage square for
the following steps.

75.

Insert and glue in F-3, F-2, and F-1 in
that order.

76.

Glue in F-7 making sure the pushrod guide hole nearest the top of the fuselage is closest to the right side when looking
towards the front.

77.

Glue in F-8 making sure the top
pushrod guide hole is to the right as in
the previous step.

78.

Glue in F-9 making sure the pushrod
guide hole is offset to the left, and then
add F-10.

79.

Double check the fuselage for
straightness at this point, then go back
and double glue all your bulkheads to
the fuse sides.

80.

Install the two 1/8" (3.2mm) nylon pushrod guide tubes. Sand the bottoms of F-1, F-2, and F-3 to an angle to match the
curvature of the F-16 bottom sheeting.

81.

Notice the notch at the rear of F-13. This notch engages the tab on the bottom of
F-5. Glue an F-13 to F-5 and F-4, making sure that the front of F-13 centers on F-
1. When these are dry glue to F-3, F-2, and F-1.

82.

Laminate the second F-13 on top of the one that is glued to the formers.

NOTE: If you are installing landing gear, now is the time to make provisions for
the tail wheel. Refer to the drawing below. If you are not adding landing gear to
your model, proceed to the next step.

«
...
13
14
15
16
17
...
»

Summary of Contents for DORN IER Do 217





























Reviews:

No comments