manualshive.com logo in svg

SIG DORN IER Do 217, Assembly Manual, Page: 18 / 28

Share
Download
SIG DORN IER Do 217 Assembly Manual Download Page 18

. 

100. Glue HF to the front of the hatch, centered on F-2.
 
101.

 
There are four HS's on sheet #6. Bevel the bottom of one of these to sit flush on the hatch bottom and snug against F-3T. 
Now do the same for the other side.

 
102.

 
Laminate the other two HS's to the outside of the two that are glued down in the same way.
 

 

 

 
103.

 
While the hatch is still pinned in place drill a hole with a 1/8" (3.2mm) bit through the hole in the front of HF through former 
H-2.

 
104.

 
Remove the hatch from the fuselage and glue a 3/8" (9.5 mm) piece of 1/8" (3.2mm) dowel into the front of the hatch so that 
about 3/16" (4.8mm) sticks out the front.

 
105.

 
Sand a flat area on the top front part of the hatch sides and glue down the 1/4"x1-3/4"x1-1/2" (6.4x44.5x38.1mm) top block. 
Sand this part flush with the front of the hatch and the instrument panel in the rear then glue in HP.

 
106.

 
Pin the hatch assembly back onto the fuselage and rough shape the nose back to the wing opening.
 

 

 

 

AIRFRAME ASSEMBLY

 
107.

 
Sand a 2" (50.8mm) wide flat at the 
trailing edge and leading edge in the 
center of the wing. This will allow F-4T to 
slip between F-4 and the leading edge of 
the wing. Mark the exact center of F-6 
and F-4. See Drawing.

 
108.

 
Fit wing onto the fuselage lining the 
centerline of the wing up to the centers 
you marked on the bulkheads and to 
make sure there is room for F-4T at the 
leading edge.

 
109.

 
Glue the 3/16" (4.8mm) dowel into the 
hole in F-4T so that 1/4" (6.4mm) 
protrudes from the front, then cut the 
dowel on the backside off flush with the 
bulkhead.

Summary of Contents for DORN IER Do 217





























Reviews:

No comments