Siemens WL Series, Operating Instructions Manual

Page: 348 / 362

25 – 9
WL Circuit Breaker
Function Overview of the Electronic Trip Units
Basic Functions ETU748 ETU755 ETU776
Long-time overcurrent protection
✔ ✔ ✔
Function can be switched ON/OFF – – –
Setting range IR = In x … 0.4, 0.45, 0.5, 0.55, 0.4 … 1 (step: 1A) 0.4 … 1 (step: 1A)
0.6, 0.65, 0.7, 0.8,
0.9, 1
Switch-selectable overload protection
(
I2t or I4t dependent function)
✔ ✔
(via communications)
✔
Setting range of time delay class tR at I
2t
(seconds) 2, 3.5, 5.5, 8, 10, 2 … 30 (step: 0.1s) 2 … 30 (step: 0.1s)
14, 17, 21, 25, 30
Setting range of time delay tR at I
4t
(seconds) 1, 2, 3, 4, 5 1 … 5 (step: 0.1s) 1 … 5 (step: 0.1s)
Thermal memory
✔
(via slide switch)
✔
(on/off via communications)
✔
(on/off via key pad
or communications)
Phase loss sensitivity at tsd=20ms (M)
✔
(on/off via communications)
✔
(on/off via key pad
or communications)
N-conductor protection –
✔ ✔
Function can be switched ON/OFF –
✔
(via slide switch)
✔
(via slide switch)
N-conductor setting range IN = In x …
– 1 0.5 … 1
Short-time delayed overcurrent protection
✔ ✔ ✔
Function can be switched ON/OFF
✔
(via rotary switch)
✔
(via communications)
✔
(via key pad or communications)
Setting range Isd = In x … 1.25, 1.5, 2, 2.5, 1.25 … 0.8 x Icw = max 1.25 … 0.8 x Icw = max
3, 4, 6, 8, 10, 12 (step: 10A) (step: 10A)
Setting range of time delay tsd, fixed
(seconds) M, 0.1, 0.2, 0.3, 0.4 M, 0.08 … 0.4, OFF (step: 0.001s) M, 0.08 … 0.4, OFF (step: 0.001s)
Switch-selectable short -time delay
short-circuit protection
(
I2t dependent function)
✔
(via rotary switch)
✔
(via communications)
✔
(via key pad or communications)
Setting range of time delay tsd at I
2t
(seconds) 0.1, 0.2, 0.3, 0.4 0.1 … 0.4 (step: 0.001s) 0.1 … 0.4 (step: 0.001s)
Zone Selective Interlocking (ZSI) function per CubicleBUS module per CubicleBUS module per CubicleBUS module
Instantaneous overcurrent protection
✔ ✔ ✔
Function can be switched ON/OFF,
Extended Instantaneous Protection
is enabled when OFF
–
✔
(via communications)
✔
(via key pad or communications)
Setting range Ii = In x … – I
i
= I
cw
= EIP
1.5 x I
n
… 0.8 x I
cs
= max, OFF= I
cw
=EIP 1.5 x I
n
… 0.8 x I
cs
= max, OFF= I
cw
=EIP
Ground fault protection
O
(field installable module)
O
(field installable module)
O
(field installable module)
Trip and alarm function
✔ ✔
(via communications)
✔
(via key pad or communications)
Detection of the ground fault current
by residual summing method
✔ ✔ ✔
Detection of the ground fault current
by direct summing method
✔ ✔ ✔
Setting range of the Ig for trip A, B, C, D, E A … E (step: 1A) A … E (step: 1A)
Setting range of the
Ig for alarm
A, B, C, D, E A … E (step: 1A)- A … E (step: 1A)
Setting range of the time delay
tg
(seconds) 0.1, 0.2, 0.3, 0.4, 0.5 0.1 … 0.5 (step: 0.001s) 0.1 … 0.5 (step: 0.001s)
Switch-selectable
ground fault protection
(
I2t / fixed)
✔ ✔ ✔
Setting range time delay
tg at I
2t
0.1, 0.2, 0.3, 0.4, 0.5 0.1 … 0.5 (step: 0.001s) 0.1 … 0.5 (step: 0.001s)
ZSI ground function per CubicleBUS module per CubicleBUS module per CubicleBUS module
✔
available
– not available
O
optional
L
N
S
I
G
Extended Instantaneous Protection (EIP) allows the WL breaker to be applied at the withstand rating of
the breaker with minus 0% tolerance; that means no instantaneous override whatsoever. EIP further
enables the circuit breaker to be applied up to the full instantaneous rating of the breaker on systems
where the available fault current exceeds the withstand rating.
Ground Fault Module cannot be removed after installation. 1
2
Notes:
M
= Motor protection setting (20 ms)
Communications = Setting the parameters of the trip unit
via the Breaker Data Adapter, MODBUS, or PROFIBUS
Key pad = Direct input at the trip unit
In
2
1
1