manualshive.com logo in svg

Siemens SITRANS RD300, Operating Instructions Manual, Page: 87 / 110

Share
Download
Siemens SITRANS RD300 Operating Instructions Manual Download Page 87

SITRANS RD300 

A5E31917845 

SITRANS RD300 – OPERATING INSTRUCTIONS  

Page 81 

Round Horizontal Tank Linearization (

rHt

) 

This function automatically calculates the volume in a round horizontal 
tank with flat ends. This function is only used when 

Total

 is set to 

no

. 

Set the display for the desired decimal point and engineering units 
before entering the round horizontal tank function. Select units, inches 
or cm for the tank dimension. Enter the diameter and the length in 
inches and the results are given in US gallons. 
The meter can be scaled to display the volume in any engineering unit. 

 

 

Note: After Scale is displayed continue pressing the Enter button until 
the meter completes the scaling of the input and display values. 

 

Changing the Volume from Gallons to Liters 

In the above graphic, entering the 48" for the diameter and 120" for the 
length of the round horizontal tank, the meter automatically calculates 
that the volume of the tank is 940.02 gallons. 
1.  Convert gallons to liters 

  1 US gallon = 3.7854 L 
  940.02 gal = 3558.4 L 

2.  Go to the 

Setup

 menu and change the decimal point to 1 decimal. 

3.  Go to the 

Program

 – 

Scale

 menu and press Enter until 

dis 2

 is 

shown on the upper display. 

4.  Press Enter and change the display 2 value to 3558.4. 
5.  The meter is now displaying the volume in liters. 
 

Note: The display can be scaled to display the volume in any 
engineering units. 

Summary of Contents for SITRANS RD300















































































































Reviews:

No comments