manualshive.com logo in svg

Siemens SITRANS RD300, Operating Instructions Manual, Page: 84 / 110

Share
Download
Siemens SITRANS RD300 Operating Instructions Manual Download Page 84

SIT SITRANS RD300RANS RD300 

Page 78 

SITRANS RD300 – OPERATING INSTRUCTIONS 

A5E31917845 

Modbus RTU Serial Communications (

serial

) 

The meter is equipped with serial communications capability as a 
standard feature using Modbus RTU Serial Communication Protocol. 
To communicate with a computer or other data terminal equipment, an 
RS-232, RS-485, or USB adapter (7ML19306AJ) option is required. 

 

WARNING: Do not connect any equipment other 
than Siemens’s expansion modules, cables, or 
meters to the RJ45 M-LINK connector. Otherwise 
damage will occur to the equipment and the meter. 

 

Note: More detailed instructions are provided with each optional 
serial communications adapter. 

 

Note: Refer to the SITRANS

 

RD300 Modbus Register Tables 

located at www.siemens.com for details. 

 

 

When using more than one meter in a multi-drop mode, each meter 
must be provided with its own unique address. The meter address 
(Slave ID) may be programmed between 1 and 247. The transmit delay 
may be set between 0 and 199 ms. The parity can be set to even, odd, 
or none with 1 or 2 stop bits. 
 

Summary of Contents for SITRANS RD300















































































































Reviews:

No comments