manualshive.com logo in svg

Siemens SITRANS RD300, Operating Instructions Manual, Page: 42 / 110

Share
Download
Siemens SITRANS RD300 Operating Instructions Manual Download Page 42

SIT SITRANS RD300RANS RD300 

Page 36 

SITRANS RD300 – OPERATING INSTRUCTIONS 

A5E31917845 

Setting the Display Parameter & Intensity (

dsplay

) 

The upper display (

line 1

) can be programmed to display:  

1.  Process value 1 (PV1) 
2.  Process value 2 (PV2) 
3.  Percent of PV1 (PCT) 
4.  Relay set points 
5.  Max & min values 
6.  Modbus input 
7.  Display reading and units 
8.  Display gross 
9.  Toggle net & gross 

The lower display (

line 2

) can be programmed to display: 

1.  Unit 
2.  Process value 1 (PV1) 
3.  Process value 2 (PV2) 
4.  Percent of PV1 (PCT) 
5.  Relay set points 
6.  Max & min values 
7.  Engineering units or custom legends 
8.  Modbus input 
9.  Off (no display) 
10.  Toggle reading and units 
11.  Display gross 
12.  Toggle net/gross 

 

Display Intensity:

 The meter has eight display intensity levels to give 

the best performance under various lighting conditions. Select intensity 
8 for outdoor applications. The default intensity setting is 8. 

Summary of Contents for SITRANS RD300















































































































Reviews:

No comments