Siemens SITRANS RD300 Operating Instructions Manual Download Page 3

Page: 3 / 110

SITRANS RD300

Table of Contents

SITRANS RD300 ------------------------------------------------------------ 1

Benefits ------------------------------------------------------------------------------ 1

SAFETY NOTES ------------------------------------------------------------ 2

The Manual ------------------------------------------------------------------------- 2

SAFETY INFORMATION ------------------------------------------------- 3

INSTALLATION ------------------------------------------------------------- 4

Unpacking --------------------------------------------------------------------------- 4

Panel Mounting Instructions -------------------------------------------------- 4

Mounting Dimensions --------------------------------------------------------- 5

Transmitter Supply Voltage Selection (P+, P-) ------------------------- 6

Connections ------------------------------------------------------------------------ 6

Connectors Labeling ----------------------------------------------------------- 7

Power Connections ------------------------------------------------------------ 7

Signal Connections ------------------------------------------------------------ 8

Modbus RTU Serial Communications ------------------------------------- 9

Relay Connections ------------------------------------------------------------- 9

Switching Inductive Loads -------------------------------------------------- 10

F4 Digital Input Connections ----------------------------------------------- 11

4-20 mA Output Connections ---------------------------------------------- 11

Analog Output Transmitter Power Supply ------------------------------ 11

External Relay & Digital I/O Connections ------------------------------ 12

Interlock Relay Feature ----------------------------------------------------- 13

SETUP AND PROGRAMMING ---------------------------------------- 14

MeterView Pro Software ------------------------------------------------------ 15

MeterView Pro Installation ------------------------------------------------- 15

Front Panel Buttons and Status LED Indicators --------------------- 17

Display Functions and Messages ----------------------------------------- 18

Setting Numeric Values ------------------------------------------------------ 22

Configuring the Meter Basic Function ---------------------------------- 23

Configuring as a Single Process Display ------------------------------- 24

Configuring as a Rate/Total Meter --------------------------------------- 25

Main Menu (Process) ---------------------------------------------------------- 26

Setting Up the Process Meter (

setup

) ----------------------------------- 27

Setting the Process Input Signal (

Input

) ------------------------------- 28

Setting the Input Units or Custom Tags (

units

) ---------------------- 29

Setting the Decimal Point (

dEc pt

) -------------------------------------- 30

Programming the Meter (

prog

) ------------------------------------------- 31

Summary of Contents for SITRANS RD300















































































































Search results

Summary of Contents for SITRANS RD300

Reviews:

Siemens SITRANS RD300, Operating Instructions Manual, Page: 3 / 110

Search results

Summary of Contents for SITRANS RD300

Reviews: