manualshive.com logo in svg

Siemens SITRANS RD300, Operating Instructions Manual, Page: 14 / 110

Share
Download
Siemens SITRANS RD300 Operating Instructions Manual Download Page 14

SIT SITRANS RD300RANS RD300 

Page 8 

SITRANS RD300 – OPERATING INSTRUCTIONS 

A5E31917845 

Signal Connections 

Signal connections are made to a six-terminal connector labeled  
SIGNAL. The COM (common) terminal is the return for the 4-20 mA and 
the 

10 V input signals. 

Current and Voltage Connections 

The following graphics show examples of current and voltage 
connections. 
There are no switches or jumpers to set up for current and voltage inputs. 
Setup and programming is performed through the front panel buttons. 

 

Transmitter Powered by Internal Supply 

 

 

Transmitter Powered by Ext. Supply or Self-Powered 

The current input is protected against current overload by a resettable 
fuse. The display may or may not show a fault condition depending on 
the nature of the overload. 
The fuse limits the current to a safe level when it detects a fault 
condition, and automatically resets itself when the fault condition is 
removed. 

Summary of Contents for SITRANS RD300















































































































Reviews:

No comments