manualshive.com logo in svg

Siemens SITRANS RD300, Operating Instructions Manual, Page: 85 / 110

Share
Download
Siemens SITRANS RD300 Operating Instructions Manual Download Page 85

SITRANS RD300 

A5E31917845 

SITRANS RD300 – OPERATING INSTRUCTIONS  

Page 79 

Select Menu (

SElEct

) 

The 

Select

 menu is used to select the signal input conditioner applied to 

the input (linear, square root, programmable exponent, or round 
horizontal tank), low-flow cutoff, and analog output programming. The 
multi-point linearization is part of the linear function selection. 

 

 

Note: 

Count

 menu is only available when 

TOTAL

 is 

enabled. To enable 

TOTAL

 see Configuring as a Rate/Total 

Meter on page 25. 

Signal Input Conditioning (

Functn

) 

The 

Function

 menu is used to select the signal input conditioner 

 applied to the input: linear, square root, programmable exponent, or 
round horizontal tank volume calculation. The multi-point linearization is 
part of the linear function selection. 
 
Meters are set up at the factory for linear function with 2-point 
linearization. The linear function provides a display that is linear with 
respect to the input signal. 

Summary of Contents for SITRANS RD300















































































































Reviews:

No comments