Siemens SITRANS RD300 Operating Instructions Manual Download Page 72 | Manualshive

Page: 72 / 110

Siemens SITRANS RD300 Operating Instructions Manual Download Page 72

SIT SITRANS RD300RANS RD300

Page 66

SITRANS RD300 – OPERATING INSTRUCTIONS

A5E31917845

Scaling the Meter (

SCALE

)

The process inputs (4-20 mA and



10 VDC) can be scaled to display

the process variable in engineering units.
A signal source is not needed to scale the meter; simply program the
inputs and corresponding display values.

For instructions on how to program numeric values see

Setting Numeric Values

, page 22.

Error Message (

Error

)

An error message indicates that the calibration or scaling process was
not successful.
After the error message is displayed, the meter reverts to the input prior
to the failure during calibration or scaling and to input 1 during internal
calibration, allowing the appropriate input signal to be applied or
programmed.
The error message might be caused by any of the following conditions:
5. Input signal is not connected to the proper terminals or it is

connected backwards.

6. Wrong signal selection in

Setup

menu.

7. Minimum input span requirements not maintained.
8. Input 1 signal inadvertently applied to calibrate input 2.

«
...
70
71
72
73
74
...
»

Summary of Contents for SITRANS RD300















































































































Reviews:

No comments