Siemens SIMOTION TB30 Manual Download Page 32

Page: 32 / 150

Description

1.9 CompactFlash card

SIMOTION D4x5-2

Manual, 02/2012

Properties of the CompactFlash card

The CompactFlash card is essential for operation of the SIMOTION D4x5-2. The

CompactFlash card is not supplied with the SIMOTION D4x5-2 and must be ordered

separately.
The SIMOTION Kernel (SIMOTION D4x5-2 firmware) and the software used to control the

drives (SINAMICS firmware) are contained on the CompactFlash card.
The CompactFlash card is used for
●

Backing up the technology packages and user data (programs, configuration data,

parameter assignments).

●

Update (e.g. SIMOTION firmware update).

The licenses for the technology functions are linked to the serial number of the

CompactFlash card. This means the CompactFlash card can be inserted in a different

SIMOTION D without having to change the licenses.
The CompactFlash card is supplied in a bootable format with the latest SIMOTION Kernel

and drive software. Please note that a CompactFlash card with a D4x5 kernel/drive software

cannot run on a D4x5-2. The same applies for the reverse situation.
If an error occurs, all LEDs flash yellow with 2 Hz. An entry is also made in the diagnostic

buffer and the D4x5-2 does not start.
Licenses purchased for SIMOTION D can be used for both the D4x5 and D4x5-2.

CAUTION

The CompactFlash card may only be inserted or removed when the system is de-

energized. The SIMOTION D4x5-2 is in a de-energized state when all the LEDs are off.

Additional information

For additional information about inserting, changing, writing and formatting the

CompactFlash card, refer to the

SIMOTION D4x5-2 Commissioning and Hardware

Installation Manual.

Summary of Contents for SIMOTION TB30























































































































































Search results

Summary of Contents for SIMOTION TB30

Reviews:

Related manuals for SIMOTION TB30

Brands by name

Popular brands

Siemens SIMOTION TB30, Manual

Search results

Summary of Contents for SIMOTION TB30

Reviews:

Related manuals for SIMOTION TB30

Brands by name

Popular brands