Siemens SIMOTION TB30 Manual Download Page 30

Page: 30 / 150

Description

1.8 Safety information

SIMOTION D4x5-2

Manual, 02/2012

1.8

Safety information

Note the following safety information when working with the Control Unit and its components.

NOTICE

The 80 mm clearances above and below the components must be observed. The unit

protects itself from overheating by shutting down.

CAUTION

An option board may only be inserted and removed when the Control Unit and option board

are disconnected from the power supply.
The CompactFlash card may only be inserted or removed when the Control Unit is

disconnected from the power supply.
The SIMOTION D4x5-2 is in a de-energized state when all the LEDs are off.

WARNING

Safe, problem-free operation of SIMOTION D Control Units assumes proper transportation,

storage, setup, and installation, as well as careful operation and maintenance.
In addition to the danger and warning information provided in the technical customer

documentation, the applicable national, local, and plant-specific regulations and

requirements must be taken into account.
Only safety extra-low voltage in accordance with EN/IEC 60950-1 may be connected to all

connections and terminals.

Summary of Contents for SIMOTION TB30























































































































































Search results

Summary of Contents for SIMOTION TB30

Reviews:

Related manuals for SIMOTION TB30

Brands by name

Popular brands

Siemens SIMOTION TB30, Manual

Search results

Summary of Contents for SIMOTION TB30

Reviews:

Related manuals for SIMOTION TB30

Brands by name

Popular brands