manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 99 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 99

Programming 

 

5.7 Configuration function blocks 

 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 

98

 

Manual, 06/2019, A5E46959434-AA 

Parameter 

The following table shows the parameters of the function block: 

 

Parameter 

Declaration  Data type  Memory 

area 

Description 

SET 

Input 
 
 

BOOL 

I, Q, M, D, 

L or Con-

stant 

Set the instance parameters of the sensor upon a rising edge. 

ADDRESS 

USInt 

I, Q, M, D, 

L or Con-

stant 

Specify the short address of the device. 
Range: 0 to 63 

INST_NUM 

USInt 

I, Q, M, D, 

L or Con-

stant 

Specify the instance number. 
Range: 0 to 31 

INST_PRM_

SET 

InstPrm-

SetDetail 

D, L 

The instance parameters of the input device (sensor).  

  INST_TY

PE 

USInt 

Refer to the Instance type of input device (Page 107) to set the 

instance type. 
Range: 1 to 4 

INST_AC

TIVE 

BOOL 

Activation of the instance. 

EVENT_

SCHEM

E 

USInt 

An instance of an input device uses the selected event source ad-

dressing according to the scheme: 

•

 

0: Instance type and instance number 

•

 

1: Short address and instance type 

•

 

2: Short address and instance number 

•

 

3: Device group and instance number 

•

 

4: Instance group and instance type 

EVENT_

FILTER 

BYTE 

The event message filter can be used to enable and disable specific 

events. Refer to Description for EVENT_FILTER  (Page 107) for the 

detailed description. 

•

 

INST_TYPE = 1 (push button), EVENT_FILTER is in the range 

of 0 to 16#FF. 

•

 

INST_TYPE = 2 (absolute input device), EVENT_FILTER is in 

the range of 0 to 16#01. 

•

 

INST_TYPE = 3 (occupancy sensor), EVENT_FILTER is in the 

range of 0 to 16#1F. 

•

 

INST_TYPE = 4 (light sensor), EVENT_FILTER is in the range 

of 0 to 16#01. 

EVENT_

PRIO 

USInt 

The sending priority of the event message. The system reactions 

are sent according to the set priority. The system reactions with 

high priority take precedence over the system reactions with low 

priority. 

TYPE_P

RM_SET 

1

 

Array[0..6] 

of BYTE 

The type-related parameters of the instance. 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments