manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 111 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 111

Diagnostic alarms 

 

6.1 Status and error displays 

 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 

110

 

Manual, 06/2019, A5E46959434-AA 

Table 6- 2 

Meaning of the TX/RX LED displays 

LED 

Meaning 

Solution 

TX 

RX 

 

Flashes 

 

Off 

Interface is transmitting 

--- 

 

Off 

 

Flashes 

Interface is receiving 

--- 

When the CM 1xDALI receives an "IDENTIFY DEVICE" command (IEC 62386-103), the 

LED Rx and Tx flash simultaneously at a frequency of 1 Hz and last about 10 seconds. 

Table 6- 3 

Meaning of the 16V displays 

LED 

Meaning 

Solution 

16V 

 

On 

CM 1xDALI integrated DALI power 16 

V power on 

--- 

 

Off 

CM 1xDALI integrated DALI power 16 

V power off 

--- 

 

Table 6- 4 

Meaning of FOV (Fault over voltage) displays 

LED 

Meaning 

Solution 

FOV 

 

On 

Detected over voltage on the DALI bus 

(between 38 V and 353 V (250 V AC)) 

Check the wiring and supply voltage of 

DALI bus 
For example, check if you connected 

the city power to the DALI bus by mis-

take. 

 

Off 

The voltage on DALI bus is less than or 

equal to 20.5 V 

--- 

 

Table 6- 5 

Meaning of the PWR LED displays 

LED 

Meaning 

Solution 

PWR 

 

On 

Power on (supply voltage present) 

--- 

 

Off 

Power off (supply voltage missing) 

Check the supply voltage  

 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments