manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 122 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 122

 

Glossary 

 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 
Manual, 06/2019, A5E46959434-AA 

121

 

Error hold-off time 

The ERROR HOLD-OFF TIME specifies the minimum time an error must be continuously 

present in order to be indicated Total operation time. 

Event 

An instance report, characterized by its event number, of a change or a defined sequence of 

changes of its input value 

Fast fade time 

The Fast Fade Time is used instead of the Fade Time if the Fade Time is equal to 0. The 

Fast Fade Time can be set to zero or to any value in the range "Min Fast Fade Time". 

Function test 

Test to check the integrity of the circuit and the correct operation of a lamp, a changeover 

device and the self-contained battery. 

Hold time 

The hold timer is only implemented for movement based sensors. 

Hysteresis 

Define a hysteresis band to direct impact on how sensitive the input device responds to 

changes of illuminance level and therefore event generation. 

Input device 

Control device that is connected to the DALI bus and sends commands using a multi-master 

transmitter in order to distribute information about user actions and/or sensor values. 

Instance 

Analogue or binary signal processing unit of an input device 

PLC 

Programmable Logic Controller 

Power on color 

The color that the device shows when the device is turned on. 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments