manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 68 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 68

 

Programming 

 

5.7 Configuration function blocks 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 
Manual, 06/2019, A5E46959434-AA 

67

 

5.7

 

Configuration function blocks 

Configuration function blocks are used for configuring the parameters of all the DALI 

devices.  
These function blocks allow to store configuration data in the CM 1xDALI module. 
The configuration in the modules database can be built up by uploading the physical devices 

or by configuring from the CPU. A stored configuration can be easily queried and modified by 

these function blocks. 

5.7.1

 

DALI_ECG_ADD 

Description 

DALI_ECG_ADD is used for adding or modifying one configured control gear.   

●

 

In order to add one configured control gear, you must set the device type of the control 

gear. 

●

 

This function block does not send any command to the DALI bus, and the CM 1xDALI 

saves the data of the added devices (refer to data flow path 1 (Page 23)). 

●

 

After adding the device by this function block, the parameters you set by other function 

blocks (for example, DALI_ECG_SET_BASIC_PARAM (Page 72) and 

DALI_ECG_SET_GROUP (Page 83)) are saved in the CM 1x DALI. 

●

 

The device is marked as configured after the device type is set. Refer to the output 

parameter CONFIGURED of DALI_DEV_QUERY_ADDR (Page 37). 

●

 

All of the setting parameters are saved in the CM 1xDALI until the device is deleted by 

using DALI_ECG_DELETE (Page 69) or reset by using DALI_DEV_RESET (Page 104). 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments