Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 29

Page: 29 / 126

Programming

5.3 System function blocks

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0)

Manual, 06/2019, A5E46959434-AA

Parameter Decla-

ration

Data

type

Memory

area

Description

EVENT_S

CHEME

USInt

I, Q, M,

D, L

Event characterization that identifies the source of the event:

•

0~4: Normal event message

•

255: Power cycle event

Scheme of the

event

255

EVENT_S

RC_1

USInt

I, Q, M,

D, L

First event

source infor-

mation

Instance

type

Short

address

Short

ad-

dress

Device

group

In-

stance

group

Group

EVENT_S

RC_2

USInt

I, Q, M,

D, L

Second event

source infor-

mation

Instance

number

Instance

type

In-

stance

number

In-

stance

type

In-

stance

type

Short

ad-

dress

EVENT_I

NFO

WORD

I, Q, M,

D, L

When EVENT_SCHEME

≤ 4, the lower 10 bits of EVENT_INFO indicate the

event data.
When EVENT_SCHEME = 255, EVENT_INFO shows "16#0000".
For the detailed meaning of EVENT_INFO in DALI standard, refer to the

following section "Parameter EVENT_INFO".

RSV_MS

BOOL

I, Q, M,

D, L

The status of the reserved message. When the CM 1xDALI receives a re-

served message, the RSV_MSG remains true for one cycle:

•

RSV_MSG = 0: No reserved message

•

RSV_MSG = 1: A reserved message is received.

RSV_MS

G_LEN

USInt

I, Q, M,

D, L

The bit length of the reserved message

RSV_MS

G_VAL

DWORD I, Q, M,

D, L

The bit stream of the reserved message

For a valid device group, group of EVENT_SRC_1 indicates the lowest group; otherwise it shows "16#FF".

For a valid short address, short address of EVENT_SRC_2 indicates the short address of the device; oth-

erwise, it shows "16#FF".

Parameter CM_STATUS

Each Bit of the CM_STATUS indicates the different status:

Bit

Explanation of status

Bit 0

The CM 1xDALI is initializing.

Bit 1

The CM 1xDALI is set to quiescent mode by DALI command "START QUIESCENT MODE".

Bit 2

The CM 1xDALI is disabled by DALI command "DISABLE APPLICATION CONTROLLER".

Bit 3

The application controller is disabled by module parameters.

Bit 4

The DALI bus is over voltage.

Bit 5

Missing Voltage (MV)

of module input

Bit 6

The DALI bus is short-circuited.

Bit 7

Integrated DALI bus power is disabled in CM 1xDALI, and there is no external DALI bus power on DALI

bus.

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Search results

Summary of Contents for SIMATIC ET 200SP CM 1xDALI

Reviews:

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 29 / 126

Search results

Summary of Contents for SIMATIC ET 200SP CM 1xDALI

Reviews: