manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 96 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 96

 

Programming 

 

5.7 Configuration function blocks 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 
Manual, 06/2019, A5E46959434-AA 

95

 

5.7.15

 

DALI_SENSOR_QUERY_INST_PARAM 

Description 

DALI_SENSOR_QUERY_INST_PARAM is used for querying the instance parameters of the 

input device (sensor). 

●

 

When you set the input "PHY_DEV" to 1, this function block queries the parameters from 

the physical device (refer to data flow path 6 (Page 23)). 

●

 

When you set the input "PHY_DEV" to 0, this function block queries the parameters which 

are saved in CM 1xDALI (refer to data flow path 2 (Page 23)). 

You can set the instance parameters of sensor by using 

DALI_SENSOR_SET_INST_PARAM (Page 97). 

Parameter 

The following table shows the parameters of the function block: 

 

Parameter 

Declaration  Data type  Memory 

area 

Description 

QUERY 

Input 
 
 

BOOL 

I, Q, M, D, 

L or Con-

stant 

Query the instance parameters of the sensor upon a rising edge. 

ADDRESS 

USInt 

I, Q, M, D, 

L or Con-

stant 

Specify the short address of the device. 
Range: 0 to 63 

INST_NUM 

USInt 

I, Q, M, D, 

L or Con-

stant 

Specify the instance number. 
Range: 0 to 31 

PHY_DEV 

BOOL 

I, Q, M, D, 

L or Con-

stant 

Specify the location of parameters: 

•

 

PHY_DEV = 0 : Query the parameters which are saved in CM 

1xDALI. 

•

 

PHY_DEV = 1 : Query the parameters from the physical device 

by sending commands. 

CM_DALI 

InOut 

"DALI_CT

RL" 

 

The data block of DALI_CTRL specifies the CM 1xDALI which 

communicates with the current function block. 

BUSY 

Output 

BOOL 

I, Q, M, D, 

L 

Status parameter: 

•

 

BUSY = 0: Processing of job is terminated. 

•

 

BUSY = 1: Job is still being committed. 

 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments