manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 16 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 16

 

Wiring 

 

3.2 Installing position 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 
Manual, 06/2019, A5E46959434-AA 

15

 

3.2

 

Installing position 

 

 

Note 
When installing and connecting up the CM 1xDALI, refer to the instructions in the system 

manual SIMATIC ET 200SP Distributed I/O system 

(

https://support.industry.siemens.com/cs/ww/en/view/58649293

) note the information in the 

document "Use of subassemblies/modules in a Zone 2 Hazardous Area" that you will find on 

the Internet at the following address: 
Link: (

https://support.industry.siemens.com/cs/ww/en/view/78381013

) 

 

 

NOTICE 
Installation location - Dependency of the temperature range 
The upper and lower ventilation slits of CM 1xDALI cannot be covered, allowing adequate 

ventilation. Above and below the module, there must be a clearance of 25 mm to allow air 

to circulate and prevent overheating. 

 

 

Installation position 

Installation position of the CM 1xDALI 

Horizontal installation of the CM 1xDALI 

 

Vertical installation of the CM 1xDALI 

 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments