manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 43 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 43

Programming 

 

5.5 Control gear dimming function blocks 

 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 

42

 

Manual, 06/2019, A5E46959434-AA 

5.5.2

 

DALI_ECG_SWITCH_DIM 

Description 

DALI_ECG_SWITCH_DIM is used for controlling the control gear (refer to data flow path 5 

(Page 23)), and has the following features: 

●

 

If ON_UP sets to 1 and remains for the time which is shorter than the value of 

SHORT_PRESS, and then resets to 0, the control gear is switched on. 

●

 

If OFF_DOWN sets to 1 and remains for the time which is shorter than the value of 

SHORT_PRESS, and then resets to 0, the control gear is switched off. 

●

 

If ON_UP sets to 1 and remains for the time which is longer than the value of 

SHORT_PRESS, the control gear is dimming up until the ON_UP sets to 0. 

●

 

If OFF_DOWN sets to 1 and remains for the time which is longer than the value of 

SHORT_PRESS, the control gear is dimming down until the OFF_DOWN sets to 0. 

●

 

If the level of the control gear is 0, the level cannot be changed by dimming up. 

●

 

If the level of the control gear is MIN_LEVEL, the level cannot be set to 0 by dimming 

down. 

 

 

Note 
Do not set the "ON_UP" and "OFF_DOWN" to 1 at the same time. Otherwise the error code 

"16#88" is shown in the output parameter STATUS. 

 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments