manualshive.com logo in svg

Siemens SIMATIC ET 200SP CM 1xDALI, Manual, Page: 73 / 126

Share
Download
Siemens SIMATIC ET 200SP CM 1xDALI Manual Download Page 73

Programming 

 

5.7 Configuration function blocks 

 

ET 200SP Communication module CM 1xDALI (6ES7137-6CA00-0BU0) 

72

 

Manual, 06/2019, A5E46959434-AA 

Parameter 

Declaration  Data type  Memory 

area 

Description 

EXT_FA

DE_MUL 

USInt 

Multiplier of the extend fade time 
Range: 0 to 5  
EXT_FADE_MUL 

extemdedFadeTimeMultiplier 

0 

0 ms 

1 

100 ms 

2 

1 s 

3 

10 s 

4 

1 min 

In case FADE_TIME = 0, extended fade time is used, fade time = 

extendedFadeTimeBase * extemdedFadeTimeMultiplier  
Note: Extended fade time is only supported by devices compliant 

with DALI 2.0. If the device doses not support extended fade time, 

the value of EXT_FADE_TIME_BASE and EXT_FADE_TIME_MUL 

shows 0. 

ECG_TY

PE 

USInt 

Device type of control gears. Refer to Electric control gear (ECG) 

type  (Page 107). 

DEV_VE

R 

USInt 

The device version. If you set the input PHY_DEV to 0, the value of 

DEV_VER is 0. 
The version is in the format "x.y". The major version number x is 

placed in bits 7 to 2, and the minor version number y is placed in 

bits 1 to 0. 

PHM 

USInt 

Physical minimum level. 
If PHY_DEV = 0, the value of PHM is 0. 

5.7.4

 

DALI_ECG_SET_BASIC_PARAM 

Description 

DALI_ECG_SET_BASIC_PARAM is used for setting the basic parameters of DALI control 

gears. 

●

 

If the status of control gear is configured (for example, control gear is added by using 

DALI_ECG_ADD (Page 67)), the parameters are saved in the CM 1xDALI (refer to data 

flow path 1 (Page 23)) and sent to the physical device (refer to data flow path 5 

(Page 23)). 

●

 

If the status of control gear is not configured, the parameters are only sent to the physical 

device (refer to data flow path 5 (Page 23)). 

You can query the basic parameter of control gear by using 

DALI_ECG_QUERY_BASIC_PARAM (Page 70). 

Summary of Contents for SIMATIC ET 200SP CM 1xDALI































































































































Reviews:

No comments