manualshive.com logo in svg

Siemens Servo i, Service Manual, Page: 6 / 70

Share
Download
Siemens Servo i Service Manual Download Page 6

Siemens-Elema AB

Important

Servo

…

E382 E407E 061 01 01 02

1 - 6

Environmental declaration

Purpose

This environmental declaration is for a Servo

…

 basic

unit including the carrier and one battery.
Letters codes within brackets refers to the

Functional Block Diagram in chapter Diagrams.

Components with special environmental concern

Components listed below shall be disposed of in an

environmentally safe way.
Printed circuit boards
• PC 1770 Main back-plane
• PC 1771 Control, including a Lithium battery (C)
• PC 1772 Monitoring, including Lithium battery (M)
• PC 1775 Plug-and-Play back-plane (P)
• PC 1777 Panel (U)
• PC 1778 Standard connectors & DC/DC (P)
• PC 1780 Pneumatic back-plane (I)
• PC 1781 Pressure transducer, 2 pcs (T)
• PC 1784 Expiratory channel (F)
• PC 1785 Exp. channel connector (E)
• PC 1786 Exp. channel cassette (E)

Other electronics
• TFT assembly including backlight (U)
• Touch screen (U)
• O

2

 cell, containing Pb (I)

• Air module, containing multiple PC boards (I)
• O

2

 module, containing multiple PC boards (I)

• AC/DC Converter, containing PC boards (P)
• Exp. valve coil (E)
• Safety valve pull magnet (I)

Construction materials

The construction materials used in Servo

…

 in % of

the total weight.

Metal – total 77%
• Aluminium 70%
• Steel, zink, brass 8%

Polymeric material – total 9%
• PA (Polyamide)
• POM (Polyoxymethylene)
• SI (Silicone)
• TPE (Thermoplastic elastomer)
• PUR (Polyurethane)
• ABS (Acrylicnitrilebutadienstyrene)
• EPDM (Ethylenepropylenedienemonomer)
• PTFE (Polytetrafluoroethylene)
• FPM (Fluororubber)
• NBR (Nitrilerubber)
• PP (Polypropylene)
• PVC (Polyvinyl chloride)
• PS (Polystyrene)

Electronics – total 14%
• Accumulators Nickel Metalhydride
• Printed circuit boards, cables etc.

Others – very small amounts
• Sterile filter paper of glass fibre

Important

1

Summary of Contents for Servo i







































































Reviews:

No comments