Siemens SCALANCE XP208EEC Operating Instructions Manual Download Page 3

Page: 3 / 96

Table of contents

Introduction ........................................................................................................................................... 5

Safety notices ........................................................................................................................................ 9

Recommendations on network security .............................................................................................. 11

Description of the device..................................................................................................................... 17

4.1

Product overview ............................................................................................................... 17

4.2

Device views...................................................................................................................... 24

4.2.1

SCALANCE XP208 and SCALANCE XP208EEC ...................................................................... 24

4.2.2

SCALANCE XP208PoE EEC .................................................................................................. 25

4.2.3

SCALANCE XP216 and SCALANCE XP216EEC ...................................................................... 26

4.2.4

SCALANCE XP216PoE EEC .................................................................................................. 27

4.3

LED display ........................................................................................................................ 28

4.3.1

Overview ........................................................................................................................... 28

4.3.2

"RM" LED............................................................................................................................ 28

4.3.3

"SB" LED............................................................................................................................. 29

4.3.4

"F" LED............................................................................................................................... 29

4.3.5

LEDs "DM1" and "DM2"....................................................................................................... 29

4.3.6

LEDs "L1" and "L2" .............................................................................................................. 30

4.3.7

Port LEDs ........................................................................................................................... 31

4.4

RESET button ..................................................................................................................... 33

4.5

SELECT / SET button ........................................................................................................... 35

4.6

C-PLUG .............................................................................................................................. 37

4.6.1

Function of the C-PLUG ...................................................................................................... 37

4.6.2

Replacing the C-PLUG......................................................................................................... 38

4.7

Power over Ethernet (PoE).................................................................................................. 41

Installation........................................................................................................................................... 45

5.1

Safety notices for installation ............................................................................................. 45

5.2

Types of installation ........................................................................................................... 48

5.3

Wall mounting ................................................................................................................... 49

5.4

Wall mounting ................................................................................................................... 50

5.5

Rack mounting................................................................................................................... 51

Connecting up ..................................................................................................................................... 53

6.1

Safety when connecting up................................................................................................ 53

6.2

Industrial Ethernet ............................................................................................................. 56

6.2.1

Industrial Ethernet ............................................................................................................. 56

6.3

24 VDC power supply......................................................................................................... 59

6.4

54 VDC power supply......................................................................................................... 62

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

Summary of Contents for SCALANCE XP208EEC

































































































Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Related manuals for SCALANCE XP208EEC

Brands by name

Popular brands

Siemens SCALANCE XP208EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Related manuals for SCALANCE XP208EEC

Brands by name

Popular brands