Siemens SCALANCE XP208EEC Operating Instructions Manual Download Page 21

Page: 21 / 96

* Available in different lengths

Cabinet feedthrough

Component

Description

Article number

IE M12 PANEL FEED‐
THROUGH

Cabinet feedthrough for conversion from
M12 connector technology (D-coded,
IP65) to RJ-45 connector technology
(IP20)
pack of 5

6GK1 901-0DM20-2AA5

IE M12 PANEL FEED‐
THROUGH PRO

Cabinet feedthrough for conversion from
M12 connector technology (D-coded,
IP65) to M12 connector technology (D-co‐
ded, IP65)
pack of 5

6GK1 901-0DM30-2AA5

IE M12 PANEL FEED‐
THROUGH 4X2

Cabinet feedthrough for conversion from
M12 connector technology (X-coded,
IP65/67) to R-45 connector technology (X-
coded, IP20)
pack of 5

6GK1 901-0DM40-2AA5

Power supply unit

Component

Description

Article number

SITOP PSU100P

Stabilized power supply, input: 120 to 230
VAC, output 24 VDC/5A IP67

6EP1 333-7CA00

Stabilized power supply, input: 120 to 230
VAC, output 24 VDC/8A IP67

6EP1 334-7CA00

* Available in different lengths

Energy cable

Component

Description

Article number

Energy cable 2 x 0.75

Energy cable for connection of signaling
contact and power supply 24 VDC, stran‐
ded wire 2 x 0.75 mm

, capable of trailing,

not assembled
Sold by the meter

6XV1 812-8A

Robust Energy Cable 4 x 0,75 Energy cable for connection of power sup‐

ply 24 VDC, 4-wire stranded 2 x 0.75 mm

robust, flexible, not assembled
Sold by the meter

6XV1 801-2A

M12 PLUG-IN CABLE

Flexible plug-in power cable to connect
the power supply 24 VDC, 4-wire, preas‐
sembled with a 4-pin M12 plug and an
M12 socket (A-coded)

6XV1 801-5D*

* Available in different lengths

Description of the device

4.1 Product overview

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

Summary of Contents for SCALANCE XP208EEC

































































































Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Related manuals for SCALANCE XP208EEC

Brands by name

Popular brands

Siemens SCALANCE XP208EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Related manuals for SCALANCE XP208EEC

Brands by name

Popular brands