Siemens SCALANCE XP208EEC Operating Instructions Manual Download Page 27

Page: 27 / 96

4.2.4

SCALANCE XP216PoE EEC

The following figure shows an overview of the components of the SCALANCE XP216PoE EEC.

①

Cutout for hexagonal nuts

②

Keyhole hang-up mechanism

③

a Ethernet ports for Fast Ethernet (P1 - P4, P9 and P11)
b Ethernet ports for Gigabit Ethernet (P10 und P12)
c Ethernet ports for Fast Ethernet and PoE (P5 - P8, P13 and P15)
d Ethernet ports for Gigabit Ethernet and PoE (P14 and P16)

④

Grounding point

⑤

Power supply (redundant)

⑥

Signaling contact

⑦

Securing point for covering the serial interface

⑧

Serial interface

⑨

"SELECT / SET" button

⑩

LED display

⑪

Cover for:
• C-PLUG slot
• "RESET" button

Description of the device

4.2 Device views

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

Summary of Contents for SCALANCE XP208EEC

































































































Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Brands by name

Popular brands

Siemens SCALANCE XP208EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Brands by name

Popular brands