Siemens SCALANCE XP208EEC Operating Instructions Manual Download Page 79

Page: 79 / 96

8.3

Technical specifications SCALANCE XP216 and SCALANCE

XP216EEC

The following technical specifications apply to the following devices:

• SCALANCE XP216

• SCALANCE XP216EEC

Technical specifications
Attachment to Industrial Ethernet

Quantity

Connector

M12 socket

Properties

D-/X-coded, half/full duplex, MDI‑X pin
assignment

Transmission speed
• P1 - P8, P9, P11, P13 and P15
• P10, P12, P14 and P16

• 10 / 100 Mbps
• 10 / 100/ 1000 Mbps

Diagnostics interface
Serial interface

Quantity

Connector

M12 socket

Electrical data
Power supply

Rated voltage

24 VDC

Voltage range

19.2 to 28.8 V DC Safe Extra Low Volt‐
age

Design

M12 socket, 4-pin

Cable cross-section

≥ 0.25 mm

(24 AWG)

Property

Implemented redundantly

Current consumption

at 24 VDC

400 mA

Effective power loss

at 24 VDC

9.6 W

Fusing

5 A / at least 60 V
Or power supply with LPS or NEC class 2

Permitted ambient conditions
Ambient temperature

During operation up to 2000 m

-40 °C to +70 °C

During storage

-40 ℃ to +70 ℃

During transportation

-40 ℃ to +70 ℃

Relative humidity

During operation at 25 ℃

≤ 95 % no condensation

Housing, dimensions and weight
Design

compact

Housing material

Aluminum

Degree of protection

IP 65

Dimensions (W x H x D)

200 x 280 x 49 mm (57 mm incl. protective caps)

Weight

2500 g

Technical specifications

8.3 Technical specifications SCALANCE XP216 and SCALANCE XP216EEC

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

Summary of Contents for SCALANCE XP208EEC

































































































Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Related manuals for SCALANCE XP208EEC

Brands by name

Popular brands

Siemens SCALANCE XP208EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Related manuals for SCALANCE XP208EEC

Brands by name

Popular brands