Siemens SCALANCE XP208EEC Operating Instructions Manual Download Page 33

Page: 33 / 96

4.4

RESET button

Position

NOTICE
Loss of water and dust protection

If the cover is not mounted correctly, the device is not water and dust proof.

The "RESET" button is located under the cover on the top of the SCALANCE XP-200.

Figure 4-1

Position of the "RESET" button, for example on the SCALANCE XP208

Resetting the device to factory defaults

NOTICE
Previous settings

If you reset, all the changes you have made will be overwritten by factory defaults.

NOTICE
Inadvertent reset

An inadvertent reset can cause disturbances and failures in the configured network with further
consequences.

Description of the device

4.4 RESET button

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

Summary of Contents for SCALANCE XP208EEC

































































































Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Related manuals for SCALANCE XP208EEC

Brands by name

Popular brands

Siemens SCALANCE XP208EEC, Operating Instructions Manual

Search results

Summary of Contents for SCALANCE XP208EEC

Reviews:

Related manuals for SCALANCE XP208EEC

Brands by name

Popular brands