Siemens SCALANCE XP208EEC Operating Instructions Manual Download Page 9 | Manualshive

Page: 9 / 96

background image

Safety notices

2

Read the safety notices

Note the following safety notices. These relate to the entire working life of the device.

You should also read the safety notices relating to handling in the individual sections,
particularly in the sections "Installation" and "Connecting up".

CAUTION

To prevent injury, read the manual before use.

NOTICE
Loss of water and dust protection

If you open the device, it loses its water and dust protection.
• Do not open the device.

If the is not adhered to, the manufacturer's guarantee is lost.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

Do not open the device. There are no serviceable parts inside of the device.

WARNING

EXPLOSION HAZARD

Do not open the device when the supply voltage is turned on.

Safety notices when using the device according to Hazardous Locations (HazLoc)
If you use the device under HazLoc conditions you must also keep to the following safety notices
in addition to the general safety notices for protection against explosion:

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-hazardous
locations only.

This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations only.

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

9

«
...
7
8
9
10
11
...
»

Summary of Contents for SCALANCE XP208EEC

































































































Reviews:

No comments

Related manuals for SCALANCE XP208EEC

Brand: Xantech Pages: 20

Brand: 3Com Pages: 12

S7906E - Switch

Brand: 3Com Pages: 8

DXS-3410 Series

Brand: D-Link Pages: 54

Brand: RDL Pages: 4

Brand: Baxall Pages: 33

Brand: Server Technology Pages: 12

DSR Series DSR1030

Brand: Avocent Pages: 8

Brand: A-Neuvideo Pages: 26

Brand: Taiden Pages: 21

Brand: Contec Pages: 38

Brand: BluStream Pages: 4

pro-trim PT1000

Brand: Seastar Solutions Pages: 2

Brand: SMC Networks Pages: 2

Brand: Dahua Pages: 12

Brand: AV-Box Pages: 11

IMI Sensors 691A80

Brand: PCB Piezotronics Pages: 15

Giga-AcessEtherLinx-II

Brand: IMC Networks Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands